WPC boards for upright fencing - a durable and aesthetic solution with a 15-year warranty
Partition wall with upright Woodcore boards
We have 5 different profiles of Woodcore boards available for upright partitions:
- Solid board - 57/32
- Solid board - 100
- Solid board - 128
- Rhombus profile - 67
- KUBO profile - 80/42
Below are four examples of a partition wall with different board profiles. On the left is an exhibit of a 5.7 cm or 3.2 cm wide, 5.8 m long, solid plank partition. Next to it is a barrier with 10 cm wide and 5.8 m long solid boards. Then comes a barrier made of 12.8 cm wide and 2.2 m long solid boards. On the far right of the picture are the planks for the ROMB profile partition wall, 6,7 cm wide, 5,8 m long.
The maximum spacing between the two horizontal tubes depends on the type of aluminium inside the profile. The board has a concealed screw-in.
The maximum spacing between the horizontal pipes shall be
80 cm.
The maximum spacing between the horizontal pipes shall be
100 cm.
The maximum spacing between the horizontal pipes shall be 110 cm. Angle brackets must be mounted on the horizontal tubes; the rhombus profile is fixed through the bracket. The fixing is hidden.
Characteristics of fixing the boards to the structure:
The minimum distance between the screw and the edge of the cut is 3 cm. For a panel-mounted structure (balcony, courtyard fence), the maximum bolt offset from the cut edge is 15 cm. For side-mounted construction (balcony), the maximum bolt distance from the edge of the cut is 10 cm.
Installation of the barrier - profile FULL PLATE - 57/32
The 57-32 profile can be installed to a width of 5.7 cm or 3.2 cm, where the screw must be approximately 2/3 the depth of the profile. The standard length of the profile is 5,8 m, but it can be cut to any length. It is fastened with RF knipping screws through the pipe from the rear, so the screws are not visible. The special feature of this profile is that a hole smaller than the bolt is drilled in the composite material and a larger hole is drilled in the structure to allow the material to expand. The maximum spacing between bollards is 150 cm, regardless of the height of the barrier. The maximum distance between horizontal rails is 100 cm.
Installation of the barrier - profile POLNA DESKA - 100 and POLNA DESKA - 128
WoodCore WPC partition wall board - the 100 solid board profile is 5.8m long and the 128 solid board profile is 2.2m long and can be cut to any length. The board can also be rounded or made into any shape as it is treated like wood. The recommended spacing between the boards is 0,5cm to 3cm. It is also possible to overlap the boards - mounting from both sides. The maximum spacing between the posts is 180 cm for partitions up to 150 cm high. For taller partitions, the maximum spacing between the posts is 150 cm. When constructing the structure, please follow the professional guidance for the load-bearing capacity of the structure.
The screws are visible from the front, fixing from the front side is mandatory. Where the board is fixed into a steel tube, a larger hole than the screw diameter must be pre-drilled to allow for temperature-related expansion. The choice of screw depends on the type of structure.
A hole 1 mm larger than the screw must be drilled in the WoodCore board.
Installation of the barrier - ROMB PLATE profile
The rhombus profile is 6.7 cm wide and 5.8 m long and can be cut to any length. It is fixed with stainless-steel screws through the post into the aluminium tube in the middle of the profile from the rear side, so the screw is not visible from the front. The maximum distance between the posts with L-brackets is 145 cm. The hole in the composite material is always larger than the bolt due to expansion.
Example: for a 3.9 mm stainless-steel screw, drill a 3.2 mm hole into the aluminium tube, then enlarge the hole in the rhombus profile to 4.2–4.5 mm.
WARNING: installation of rhombus boards without the aluminium tube in the middle of the profile is NOT possible. The rhombus profile can only be purchased together with the alu tube, which is already included in the board price.
Installation of the barrier - KUBO profile
The KUBO partition wall system is installed vertically on a pre-prepared structure. The 80 × 42 × 5000/5800 mm profile has an aluminium profile inserted, which is fixed from the rear, depending on the chosen layout. Depending on the mounting position, raw or anodised aluminium shall be inserted into the KUBO profile. In the case of open installation, the cap is not sufficient to prevent the ingress of moisture into the moulding, anodised aluminium must be used. Mounting is possible on a visible width of 4,2 cm or 8 cm. The slats shall be mounted on horizontally mounted, powder-coated aluminium tubes, the spacing between the slats is optional. The maximum spacing between horizontal pipes without accessories is 120 cm. If the span of the structure is greater than 120 cm, a 20 × 60 × 2 mm aluminium tube shall be inserted in the KUBO batten, in which case a span of up to 260 cm between the horizontal beams is permitted.
Different boards for WPC vertical barrier wall:
PROFILE RHOMBUS - 67
WoodCore WPC ROMB board for rhombus profile partition with aluminium tube in the centre of the rhombus.
Dimensions: 67 x 26 x 5800 mm
KUBO PROFILE
WoodCore WPC KUBO barrier board with aluminium tube (raw or anodised) in the centre
Dimension: 80 x 42 x 5000 mm
Inside aluminium tube (left to right): 20×60×2 mm, 25×25×2 mm, 20×20×2 mm.
The choice affects the price and span of the structure
KUBO FULL BOARD - 100
WoodCore WPC Board-100 for partitioning with visible screwing.
Dimension: 100 x 12 x 5800 mm
KUBO FULL BOARD - 57/32
WoodCore WPC board profile full, screwed from the back
Dimension: 57 x 32 x 5800 mm; can be stacked on 57 or 32
Colour shades
Colour shades for profile ROMB DESKA - 67:
For the rhombus profile you can choose from the seven colours below:
** In Rustic Oak and Rustic Walnut, which have a multi-coloured look, the shade and the pattern of the spots can vary more noticeably between boards and batches.
Colour shades for profile KUBO - 80/42
Choose from four colour shades:
** In Rustic Oak and Rustic Walnut, which have a multi-coloured look, the shade and the pattern of the spots can vary more noticeably between boards and batches.
Colour shades for POLNA DESKA - 100:
The boards are only suitable for an upright barrier. For full profile boards, you can choose from the eight colours below:
** In Rustic Oak and Rustic Walnut, which have a multi-coloured look, the shade and the pattern of the spots can vary more noticeably between boards and batches.
Colour shades for profile POLNA DESKA - 57/32:
For 57/32 full profile boards, the colours currently available are:
** In Rustic Oak and Rustic Walnut, which have a multi-coloured look, the shade and the pattern of the spots can vary more noticeably between boards and batches.
Storage
Before installation, WoodCore WPC boards must be stored in a dry and well-ventilated place. The storage base should be flat and clean. The boards must be fully supported along their length and width. In case of improper storage, complaints cannot be accepted.
Send us an enquiry
Get your free offer! Let us know the dimensions of your partition or canopy. We need the length and height to make a quotation. In addition, please let us know which type of partition you would like to have and what the spacing would be. Please let us know the dimensions of your partition at info@roksal.com. If possible, you can also provide us with a floor plan and pictures.
The fastest way is to send your inquiry directly via the form at the button below:
Made of bamboo fibre and HDPE plastic, WPC boards provide stability and resistance even when the fence is erected upright. With a 15-year warranty and minimal maintenance, WPC boards are a long-term and durable solution.
You can also read more about the material at WPC - Wikipedia